*) Driver version updated for RBD and CephFS.
*) Dockerfile updated to have 1.1.0 tag
*) Deployment yamls updated to 1.1.0 yamls.
Signed-off-by: Humble Chirammal <hchiramm@redhat.com>
As detailed in issue #279, current lock scheme has hash
buckets that are count of CPUs. This causes a lot of contention
when parallel requests are made to the CSI plugin. To reduce
lock contention, this commit introduces granular locks per
identifier.
The commit also changes the timeout for gRPC requests to Create
and Delete volumes, as the current timeout is 10s (kubernetes
documentation says 15s but code defaults are 10s). A virtual
setup takes about 12-15s to complete a request at times, that leads
to unwanted retries of the same request, hence the increased
timeout to enable operation completion with minimal retries.
Tests to create PVCs before and after these changes look like so,
Before:
Default master code + sidecar provisioner --timeout option set
to 30 seconds
20 PVCs
Creation: 3 runs, 396/391/400 seconds
Deletion: 3 runs, 218/271/118 seconds
- Once was stalled for more than 8 minutes and cancelled the run
After:
Current commit + sidecar provisioner --timeout option set to 30 sec
20 PVCs
Creation: 3 runs, 42/59/65 seconds
Deletion: 3 runs, 32/32/31 seconds
Fixes: #279
Signed-off-by: ShyamsundarR <srangana@redhat.com>
Deployment behaves better when a node gets disconnected from the rest of
the cluster - new provisioner leader is elected in ~15 seconds, while
it may take up to 5 minutes for StatefulSet to start a new replica.
Refer: 52d1fbcf9dFixes: #335
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
currently, we have 3 docker files(cephcsi,rbd,cephfs) in the ceph-csi repo.
[commit ](85e121ebfe)
added by John to build a single image which can act as rbd or
cephfs based on the input configuration.
This PR updates the makefile and kubernetes templates to use
the unified image and also its deletes the other two dockerfiles.
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
Existing config maps are now replaced with rados omaps that help
store information regarding the requested volume names and the rbd
image names backing the same.
Further to detect cluster, pool and which image a volume ID refers
to, changes to volume ID encoding has been done as per provided
design specification in the stateless ceph-csi proposal.
Additional changes and updates,
- Updated documentation
- Updated manifests
- Updated Helm chart
- Addressed a few csi-test failures
Signed-off-by: ShyamsundarR <srangana@redhat.com>
The kubernetes manifests and Helm templates have been updated to use
aggregated ClusterRoles. The same change has been done in Rook as well.
Refer rook/rook#2634 and rook/rook#2975
Signed-off-by: Kaushal M <kshlmster@gmail.com>
PR #290 missed the update permission to persistentvolumes.
Without that permission, you will get the following error when attaching a RBD volume to a pod:
```
Warning FailedAttachVolume 100s (x11 over 7m52s) attachdetach-controller AttachVolume.Attach failed for volume "pvc-d23f8745-60bb-11e9-bd35-5254001c78d6" : could not add PersistentVolume finalizer: persistentvolumes "pvc-d23f8745-60bb-11e9-bd35-5254001c78d6" is forbidden: User "system:serviceaccount:kube-system:rbd-csi-provisioner" cannot update resource "persistentvolumes" in API group "" at the cluster scope
```
if attacher is not enabled, we need to
create the csidriver CRD with spec
to make attachRequired as false to
skip volume attach check in kube.
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
adding the condition will help us
to easily remove the attacher later.
or even we can add else condition
if we have an alternate to attacher.
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
