This commit gets the description from remote status
instead of local status.
Local status doesn't have ',' due to which we get
array index out of range panic.
Fixes: #3388
Signed-off-by: Yati Padia <ypadia@redhat.com>
Co-authored-by: shyam Ranganathan <srangana@redhat.com>
This commit implements getVolumeReplicationInfo
to get the last sync time and update it in volume
replication CR.
Signed-off-by: yati1998 <ypadia@redhat.com>
Current code uses an !A && !B condition incorrectly to
test A:Up and B:status for a remote peer image.
This should be !A || !B as we require both conditions to
be in the specified state (Up: true, and status Unknown).
This is corrected by this commit, and further fixes:
- check and return ready only when a remote site is
found in the status output
- check if all peer sites are ready, if multiple are found
and return ready appropriately
Signed-off-by: Shyamsundar Ranganathan <srangana@redhat.com>
During ResyncVolume we check if the image
is in an error state, and we resync.
After resync, the image will move to
either the `Error` or the `Resyncing` state.
And if the image is in the above two
conditions, we will return a successful
response and Ready=false so that the
consumer can wait until the volume is
ready to use. If the image is in any
other state we return an error message
to indicate the syncing is not going on.
The whole resync and image state change
depends on the rbd mirror daemon. If the
mirror daemon is not running, the image
can be in Resyncing or Unknown state.
The Ramen marks the volume replication as
secondary, and once the resync starts, it
will delete the volume replication CR as a
cleanup process.
As we dont have a check for the rbd mirror
daemon, we are returning a resync success
response and Ready=false. Due to this false
response Ramen is assuming the resync started
and deleted the volume replication CR, and
because of this, the cluster goes into a bad
state and needs manual intervention.
fixes#3289
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
After Failover of workloads to the secondary
cluster when the primary cluster is down,
RBD Image is not marked healthy, and VR
resources are not promoted to the Primary,
In VolumeReplication, the `CURRENT STATE`
remains Unknown and doesn't change to Primary.
This happens because the primary cluster went down,
and we have force promoted the image on the
secondary cluster. and the image stays in
up+stopping_replay or could be any other states.
Currently assumption was that the image will
always be `up+stopped`. But the image will be in
`up+stopped` only for planned failover and it
could be in any other state if its a forced
failover. For this reason, removing
checkHealthyPrimary from the PromoteVolume RPC call.
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
Removed the code in checkHealthyPrimary which
makes the ceph call, passing it as input now.
Added unit test for checkHealthyPrimary function
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
Journal-based RADOS block device mirroring ensures point-in-time
consistent replicas of all changes to an image, including reads and
writes, block device resizing, snapshots, clones, and flattening.
Journaling-based mirroring records all modifications to an image in the
order in which they occur. This ensures that a crash-consistent mirror
of an image is available.
Mirroring when configured in journal mode, mirroring will
utilize the RBD journaling image feature to replicate the image
contents. If the RBD journaling image feature is not yet enabled on the
image, it will be automatically enabled.
Fixes: #2018
Co-authored-by: Madhu Rajanna <madhupr007@gmail.com>
Signed-off-by: Prasanna Kumar Kalever <prasanna.kalever@redhat.com>
Moved to add scheduling to the promote
operation as scheduling need to be added
when the image is promoted and this is
the correct method of adding the scheduling
to make the scheduling take place.
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
below are the local states of the mirrored image
"unknown" -> If the image is in an error state
means data is completely synced
"error" -> If the image is in an error state
means it needs resync
"syncing"
"starting_replay"
"replaying"
"stopping_replay"
"stopped"
If the resync is successfully started which
means the image will be in "replaying" state.
we can consider "replaying" state to report
resync succesfully going on state.
we are discarding the intermediate states like
"syncing", "starting_replay" and "stopping_replay".
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
consider the empty mirroring mode when
validating the snapshot interval and
the scheduling time.
Even if the mirroring Mode is not set
validate the snapshot scheduling details
as cephcsi sets the mirroring mode to default
snapshot.
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
nlreturn linter requires a new line before return
and branch statements except when the return is alone
inside a statement group (such as an if statement) to
increase code clarity. This commit addresses such issues.
Updates: #1586
Signed-off-by: Rakshith R <rar@redhat.com>
This commit resolves parallel test issues
and also excludes internal/util/conn_pool_test.go
as those test can't run in parallel.
Updates: #1586
Signed-off-by: Yati Padia <ypadia@redhat.com>
Mirror-snapshots can also be automatically created on a
periodic basis if mirror-snapshot schedules are defined.
The mirror-snapshot can be scheduled globally, per-pool,
or per-image levels. Multiple mirror-snapshot schedules
can be defined at any level.
To create a mirror-snapshot schedule with rbd, specify
the mirror snapshot schedule add command along with an
optional pool or image name; interval; and optional start time:
The interval can be specified in days, hours, or minutes
using d, h, m suffix respectively. The optional start-time
can be specified using the ISO 8601 time format. For example:
```
$ rbd --cluster site-a mirror snapshot schedule
add --pool image-pool --image image1 24h 14:00:00-05:00
```
Signed-off-by: Madhu Rajanna <madhupr007@gmail.com>
